How To...
GE Concord - Silence Beeping
If you would like to silence any trouble beeps on your keypad, press *(Status) or Arm and Disarm the system. The beeping will stop for 4 hours and return unless the issue has been rectified.
Simon XTi - How to Clear Troubles/Alerts
1. Press the Gear icon in the bottom right-hand corner of the screen (if there is a yellow triangle next to it, there are uncleared messages). 2. Press Listen (labelled Hear in the image below) to listen to the trouble messages and alerts (if there ...
Simon 3 - Adjusting Status Sound Volume
It is possible to adjust the volume of the Status Sound on your Simon 3 alarm panel, such as arming beeps, trouble beeps, and status beeps. The lowest volume setting is 1, the highest is 10. If you are turning down the volume of trouble beeps during ...
Simon XTi - User Guide
See attached
Simon 3 - Disconnecting Battery and Powering Down System
To disconnect the battery back up, press the top of the key pad to open the cover Take a small screw driver and gently press the tab below to open to the inside Use the screw driver to open the battery case as per below Disconnect the lead wires ...
Simon XT- Turning off Trouble Beeps
To turn off the trouble beeps at your key pad: Scroll down on the Simon XT until you see "System Programming" Immediately press "OK" Enter your Master Code and press "OK" It will display "Access Codes" Scroll down until you see "Siren Options" Press ...
GEC Concord 4 - Manuals
User Manuals can be downloaded below by clicking on the link.
GEC Concord 4 - View Event Buffer
Event buffer You have the option to view the event history for each partition of your system. These events include arming, disarming, tampers, programming entries, and more. The system master code can view all events from any partition. The ...
Simon XT - Managing User Codes
To change user codes on a Simon XT: Enter the System menu by pressing one of the scroll buttons or the OK button in the upper right of the panel. Scroll until the display shows System Programming, and then press OK The display will show Enter Code. ...
Simon XT - Rebooting Panel
1) Go to your keypad and press down on the two tabs on the top of the keypad. This will allow for the front of the keypad to swing down. 2) Disconnect the battery from the panel by taking off the positive and negative leads from the battery. 3) Find ...
Simon XTi - Managing User Codes
ADD/CHANGE USER CODES 1. Click on the GEAR icon at the bottom right then press DOWN ARROW several times 2. Press ENTER by Programming then enter your Master Code then press OK 3. Press ACCESS CODES then press the box by an empty User Code 4. Enter ...
Simon XTi - Silencing Trouble Beeps
Disabling your trouble beeps should only be done when you're aware of the reason why it's beeping 1. Press the GEAR icon at the bottom righthand corner, then press the DOWN ARROW until you see Programming 2. Press ENTER by Programming and enter the ...
Simon XT - How to Reset the Clock.
Scroll up/down until the display shows Set Clock. Press OK. The display shows Enter Code. Enter your master code with numeric keys. Press OK. Press OK again. The display now flashes the hours. Scroll up/down to set the hours. Press the OK key to ...
Simon XT - Acknowledging Status Messages
Some types of status conditions, such as alarm history, must be cleared manually. To clear system status, press Status, read and/or listen to the status messages, and then press Disarm. If the trouble condition was a low system battery, perform a ...
Simon XT - Change Volume/Vocal Settings
Please follow the below instructions to make changes to the volume levels of your beeps or panel voice. 1. Piezo Beeps: - These are the beeps the panel makes for system activity (eg. I opened the front door and my panel beeped. When I arm the panel ...
Simon XTi - Reboot/Power Cycle
If your Simon XTi has stopped responding, often a quick restart or reboot may resolve the issue. The following is a simple procedure that take about 5 minutes to complete: Carefully pull the trim ring (B) off the edges of your panel. (Use notch, C, ...
Simon XT - Turning the keypad beeps off.
1 Press the down arrow 5 times and you will see "System Programming" 2 Press OK followed by your master disarm code. 3 Press OK 4 Press the down arrow 4 times and you will see " Siren Options" 5 Press OK 6 You will see " Piezo Beeps" Press OK 7 Press ...
Simon XTi
User Manuals can be downloaded below by clicking on the link. Related Articles Simon XTi Quick Reference Guide Simon XTi Panel Battery Replacement Simon XTi - Default Screen Wireless Motion Battery Replacement
Simon XT - Power down
1) Find your alarms Transformer ( plug in adapter) Usually in the mechanical room or in a designated place you and your reed security installer talked about. 2) Go to your keypad and press down on the two tabs on the top of the keypad. This will ...
Simon XTi - Set Time
Setting Time for a Simon XTi Panel Tap on the gear in lower corner of the screen. Tap on the down arrow to the last page. Tap the Enter button next to the top option labeled "Set Date/Time" Enter you four(4) digit MASTER CODE, tap OK button To make ...